Fengerwestergaard7716

Selective catalytic reduction of NO with CO (CO-SCR) was investigated based on optimizing the operating conditions by response surface methodology (RSM) and by appropriately choosing the supported SBA-15 catalysts. The effects of the CO-SCR reaction parameters such as NOCO molar ratios and oxygen concentrations on the catalytic performance were determined by RSM to evaluate the NO conversion using a first-order polynomial model. The CuO/SBA-15 and Fe2O3/SBA-15 catalysts were synthesized by a hydrothermal method and characterized by X-ray diffraction (XRD), atomic absorption spectroscopy (AAS), N2 adsorption-desorption (BET), scanning electron microscopy coupled to energy dispersive X-Ray spectroscopy (SEM-EDS), and Fourier transform infrared spectroscopy (FTIR) to investigate the physicochemical properties of the solids. The RSM showed a very good agreement between predicted values and experimental results with the Pareto analysis confirming the accuracy and reliability of the model. The optimized results indicated the maximum NO conversion at 500 °C with using the NO to CO molar ratio of 12 (5001000 ppm) in the absence of oxygen. Under these conditions, CuO/SBA-15 catalyst achieved 99.7% of NO conversion, whereas Fe2O3/SBA-15 had 98.1% of the catalytic parameter. buy AUPM-170 Catalytic tests in CO-SCR reaction were performed on both catalysts at optimum operating conditions with CuO/SBA-15 exhibiting better performance compared to that of Fe2O3/SBA-15. The results revealed that CuO/SBA-15 was a promising catalyst for CO-SCR of NO due to the well-dispersed CuO phase on SBA-15 surface that allows the solid being more tolerant to the presence of oxygen.Water security is considered as one of the critical subjects that can arise from different issues, for instance, the injection of a poisonous pollutant into the drinking water system of a city followed by a terrorist attack. If the network lacks optimal operation to provide security against this threat, the whole population of the city can be affected by such an incident. This study aimed at preparing the optimal emergency response protocols by multi-objective particle swarm optimization (MOPSO). Furthermore, it calculates the risk of contaminants entering the network. The problem consists of three main objectives 1) minimizing the number of operational interventions, 2) minimizing the number of polluted nodes, and 3) minimizing the number of exposed individuals. The location of closed valves and opened hydrants was chosen as decision variables. The proposed method is demonstrated using a benchmark and a real network.Substrates are the main factor influencing the performance of constructed wetlands (CWs), and especially play an important role in enhancing the removal of nitrogen and phosphorus from CWs. In the recent 10 years, based on the investigation of emerged substrates used in CWs, this paper summarizes the removal efficiency and mechanism of nitrogen and phosphorus by a single substrate in detail. The simultaneous removal efficiency of nitrogen and phosphorus by different combined substrates is emphatically analyzed. Among them, the reuse of industrial and agricultural wastes as water treatment substrates is recommended due to the efficient pollutant removal efficiency and the principle of waste minimization, also more studies on the environmental impact and risk assessment of the application, and the subsequent disposal of saturated substrates are needed. This work serves as a basis for future screening and development of substrates utilized in CWs, which is helpful to enhance the synchronous removal of nitrogen and phosphorus, as well as improve the sustainability of substrates and CWs. Moreover, further studies on the interaction between different types of substrates in the wetland system are desperately needed.PM0.1 has been believed to have adverse short- and long-term effects on human health. However, the information of PM0.1 that is needed to fully evaluate its influence on human health and environment is still scarce in many developing countries. This is a comprehensive study on the levels, chemical compositions, and source apportionment of PM0.1 conducted in Hanoi, Vietnam. Twenty-four-hour samples of PM0.1 were collected during the dry season (November to December 2015) at a mixed site to get the information on mass concentrations and chemical compositions. Multiple linear regression analysis was utilized to investigate the simultaneous influence of meteorological factors on fluctuations in the daily levels of PM0.1. Multiple linear regression models could explain about 50% of the variations of PM0.1 concentrations, in which wind speed is the most important variable. The average concentrations of organic carbon (OC), elemental carbon (EC), water-soluble ions (Ca2+, K+, Mg2+, Na+, NH4+, Cl-, NO3-, SO42-, C2O42-), and elements (Be, Al, V, Cr, Mn, Co, Ni, Cu, Zn, As, Se, Mo, Cd, Sb, Ba, Tl, Pb, Na, Fe, Mg, K, and Ca) were 2.77 ± 0.90 μg m-3, 0.63 ± 0.28 μg m-3, 0.88 ± 0.39 μg m-3, and 0.05 ± 0.02 μg m-3, accounting for 51.23 ± 9.32%, 11.22 ± 2.10%, 16.28 ± 2.67%, and 1.11 ± 0.94%, respectively. A positive matrix factorization model revealed the contributions of five major sources to the PM0.1 mass including traffic (gasoline and diesel emissions, 46.28%), secondary emissions (31.18%), resident/commerce (12.23%), industry (6.05%), and road/construction (2.92%).A uniformly distribution of 3 wt.% Mo (with tetrahedral coordination) on a commercial HY zeolite having both micro- and meso-pores, provided a new active catalyst which resulted 100% removal of DBT in this work. Respectively, H2O2 and acetonitrile were used as the oxidant and extraction solvent for oxidative desulfurization (ODS) at a mild condition. The structure of three-dimensional meso-pores, despite major micro-pores, was proved to be intriguing for the use of acidic HY zeolite as a support material in this process. The catalyst samples were characterized by different analyses of XRPD, XRF, FTIR, SEM, EDX, TEM, N2 adsorption desorption, BET, BJH, UV-vis, and NH3-TPD. High amounts of Mo were not in favor of the catalytic performance because of increasing non-framework polymolybdate formation, which led to decreasing meso-pore volume. Acid sites strength also decreased by increasing Mo content. The Mo active sites at a low loading of 3 wt.% reached the best performance for the complete removal of DBT (t = 90 min, T = 60 °C, catalyst/fuel = 8 g/L, O/S = 2, VSolvent/VOil = 1/2, DBT = 1000 ppm), mainly due to the presence of isolated Mo species in the framework of HY.