Bildekern6073

A small, cheap, and low-power mesh-type piezoelectric ultrasonic transducer (MPUT) from a household USB humidifier has been developed as a sonochemiluminescence generator for the first time. The ultrasonication of an MPUT facilitates the generation of reactive oxygen species to trigger sonochemiluminescence. There is no light emission of luminol without sonication. In contrast, the luminescence becomes very intense by ultrasonication using the MPUT and can be readily observed by a smart phone, enabling the visual detection of luminol without adding any coreactants. Interestingly, ascorbic acid, a common chemiluminescence quencher in the literature, increases the sonochemiluminescence in this system. As a result, a sensitive sonochemiluminescence method has been developed for the visual detection of ascorbic acid with a linear range of 1-40 μM and a limit of detection (LOD) of 0.35 μM. Moreover, the visual detection of superoxide dismutase has been achieved on the basis of its quenching effect, which has a linear range of 0.05-2.0 μg/mL and a LOD of 0.018 μg/mL. Because of its advantages of low cost, small size, and low-power consumption, the USB MPUT holds great potential in sonochemiluminescence (SCL) for the development of portable and disposable analysis devices in point-of-care testing and field analysis as well as chemical education.Silver nanopowders (nano-Ag) have extremely high surface energy and are generally difficult to have an effective dispersant for their dispersion stabilization. This study proposes two brush copolymers that show a strong preference for adsorption on the nano-Ag surface via their backbone, while their side chains extend into the dispersion solvent for particle stabilization. After adding only 5 wt % (based on the mass of nano-Ag) of the proposed dispersants, the nano-Ag particles can be stably suspended without settling for at least 2 months. Besides, 5 wt % of these dispersants can well stabilize at least 40 wt % nano-Ag dispersed in di(ethylene glycol) ethyl ether, which is a common solvent for conductive inks and pastes. For applications, a thin film cast using the dispersed nano-Ag shows greatly improved surface flatness as compared to that made without the dispersant, and a low electrical resistivity of 2 × 10-5 Ω cm is obtained after the film is annealed at 170 °C for 20 min.The evaporation mechanism of miscible binary nanodroplets from heated homogeneous surfaces was studied by molecular dynamics simulations, which has never been studied before. The binary droplets contain a hydrophilic component (type-2 particles) and a hydrophobic component (type-3 particles). It is shown that liquid-liquid interaction strength (ε23) and hydrophilic particle number fraction (φ) have great influence on the surface tension, wetting characteristics, evaporation patterns, evaporation rate, and local mass flux. It is observed that when ε23 ≥ 1, or φ ≈ 0.5, the evaporation mode is the constant-contact-angle mode. Otherwise, it is the mixed mode. We found that the evaporation rate becomes faster when φ and ε23 increase. The droplets become more hydrophilic when φ increases, which promotes heat transfer efficiency between the liquid-solid interface. Besides, a larger ε23 promotes the heat transfer inside the droplet. The mass transfer to the vapor phase occurs preferentially in the vicinity of TPCL (three phase contact line) in the hydrophilic systems (θ θc), the mass flux close to the TPCL is suppressed. We found that θc ∈ (102°-106°), which is different from the theoretical one, θc = 90°. The discrepancy is attributed to the existence of the adsorption layer near the TPCL.In this article, the interaction between a designed antimicrobial peptide (AMP) G(IIKK)3I-NH2 (G3) and four typical conventional surfactants (sodium dodecyl sulfonate (SDS), hexadecyl trimethyl ammonium bromide (C16TAB), polyoxyethylene (23) lauryl ether (C12EO23), and tetradecyldimethylamine oxide (C14DMAO)) has been studied through surface tension measurement and circular dichroism (CD) spectroscopy. The antimicrobial activities of AMP/surfactant mixtures have also been studied with Gram-negative Escherichia coli, Gram-positive Staphylococcus aureus, and the fungus Candida albicans. The cytotoxicity of the AMP/surfactant mixtures has also been assessed with NIH 3T3 and human skin fibroblast (HSF) cells. The surface tension data showed that the AMP/SDS mixture was much more surface-active than SDS alone. CD results showed that G3 conformation changed from random coil, to β-sheet, and then to α-helix with increasing SDS concentration, showing a range of structural transformation driven by the different interaonic, and zwitterionic surfactants during product development, but care must be taken when AMPs are formulated with anionic surfactants, as the strong electrostatic interaction may undermine their antimicrobial activity.The prospect of ever increasing antibiotic resistance eroding currently available treatment options for bacterial infections underscores the need to continue to identify new antibiotics, preferably those that act on novel targets or with novel mechanisms of action. Bacterial gyrase B subunit (GyrB), an essential component of bacterial gyrase required for successful DNA replication, represents such a target. We describe recent examples of GyrB inhibitors and point out their potential utility for treatment of mycobacterial diseases caused by Mycobacterium tuberculosis (TB) and non-tuberculous mycobacteria (NTM). Current therapeutic options for these diseases are often suboptimal due to resistance to current standard of care antibiotics. GSK690693 A future GyrB inhibitor-based antibiotic could offer a new and effective addition to the armamentarium for treatment of mycobacterial diseases and possibly for infections caused by other bacterial pathogens. One GyrB inhibitor, SPR720, has recently completed a first-in-human clinical trial and is in clinical development for the treatment of NTM and TB infections.During the screening of active materials (AMs) for lithium-ion batteries, the solid-state lithium diffusion coefficient (DLi) is one of the most relevant descriptors used to evaluate the relevance of an AM candidate. However, for a given compound, the DLi values reported in literature span over several orders of magnitude. Therefore, through the case study of LiNi1/3Mn1/3Co1/3O2 cathode AM, new physical insights are provided to explain the dispersion of DLi values obtained through galvanostatic intermittent titration technique (GITT) . For the first time, a 3D electrochemical model (accounting for the carbon-binder domain) fed with experimental inputs is capable of highlighting the limitations of the most widely used equation for deriving DLi. Through our model, we show that these limitations arise from the influence of the carbon-binder domain location throughout the electrode and the non-homogeneous AM phasedistribution and particle size.