Fieldsabrams4556

The exploitation of epoxidized natural rubber (ENR) in electrochemical applications is approaching its limits because of its poor thermo-mechanical properties. These properties could be improved by chemical and/or physical modification, including grafting and/or crosslinking techniques. In this work, acrylonitrile (ACN) has been successfully grafted onto ENR- 25 by a radical photopolymerization technique. The effect of (ACN to ENR) mole ratios on chemical structure and interaction, thermo-mechanical behaviour and that related to the viscoelastic properties of the polymer was investigated. The existence of the -C≡N functional group at the end-product of ACN-g-ENR is confirmed by infrared (FT-IR) and nuclear magnetic resonance (NMR) analyses. An enhanced grafting efficiency (~57%) was obtained after ACN was grafted onto the isoprene unit of ENR- 25 and showing a significant improvement in thermal stability and dielectric properties. G140 cost The viscoelastic behaviour of the sample analysis showed an increase of storage modulus up to 150 × 103 MPa and the temperature of glass transition (Tg) was between -40 and 10 °C. The loss modulus, relaxation process, and tan delta were also described. Overall, the ACN-g-ENR shows a distinctive improvement in characteristics compared to ENR and can be widely used in many applications where natural rubber is used but improved thermal and mechanical properties are required. Likewise, it may also be used in electronic applications, for example, as a polymer electrolyte in batteries or supercapacitor.This paper addresses the problem of nonlinear height tracking control of an automobile active air suspension with the output state constraints and time-varying disturbances. The proposed control strategy guarantees that the ride height stays within a predefined range, and converges closely to an arbitrarily small neighborhood of the desired height, ensuring uniform ultimate boundedness. The designed nonlinear observer is able to compensate for the time-varying disturbances caused by external random road excitation and perturbations, achieving robust performance. Simulation results obtained from the co-simulation (AMESim-Matlab/Simulink) are given and analyzed, demonstrating the efficiency of the proposed control methodology.The purpose of our scoping review was to describe the current use of mHealth technology for long-term assessment of patient-reported outcomes in community-dwelling individuals with acquired brain injury (ABI). Following PRISMA guidelines, we conducted a scoping review of literature meeting these criteria (1) civilians or military veterans, all ages; (2) self-reported or caregiver-reported outcomes assessed via mobile device in the community (not exclusively clinic/hospital); (3) published in English; (4) published in 2015-2019. We searched Ovid MEDLINE(R) less then 1946 to 16 August 2019, MEDLINE InProcess, EPub, Embase, and PsycINFO databases for articles. Thirteen manuscripts representing 12 distinct studies were organized by type of ABI [traumatic brain injury (TBI) and stroke] to extract outcomes, mHealth technology used, design, and inclusion of ecological momentary assessment (EMA). Outcomes included post-concussive, depressive, and affective symptoms, fatigue, daily activities, stroke risk factors, and cognitive exertion. Overall, collecting patient-reported outcomes via mHealth was feasible and acceptable in the chronic ABI population. Studies consistently showed advantage for using EMA despite variability in EMA timing/schedules. To ensure best clinical measurement, research on post-ABI outcomes should consider EMA designs (versus single time-point assessments) that provide the best timing schedules for their respective aims and outcomes and that leverage mHealth for data collection.The loads acting on a workpiece during machining processes determine the modification of the surface of the final workpiece and, thus, its functional properties. In this work, a method that uses thermocouples to measure the temperature in precision fly-cutting machining with high spatial and temporal resolution is presented. Experiments were conducted for various materials and machining parameters. We compare experimental measurement data with results from modern and advanced machining process simulation and find a good match between experimental and simulation results. Therefore, the simulation is validated by experimental data and can be used to calculate realistic internal loads of machining processes.Infection by oncogenic human papillomavirus (HPV) is the primary cause of cervical cancer and other anogenital cancers. The majority of cervical cancer cases occur in low- and middle- income countries (LMIC). Concurrent infection with Human Immunodeficiency Virus (HIV) further increases the risk of HPV infection and exacerbates disease onset and progression. Highly effective prophylactic vaccines do exist to combat HPV infection with the most common oncogenic types, but the accessibility to these in LMIC is severely limited due to cost, difficulties in accessing the target population, cultural issues, and maintenance of a cold chain. Alternative preventive measures against HPV infection that are more accessible and affordable are therefore also needed to control cervical cancer risk. There are several efforts in identifying such alternative prophylactics which target key molecules involved in early HPV infection events. This review summarizes the current knowledge of the initial steps in HPV infection, from host cell-surface engagement to cellular trafficking of the viral genome before arrival in the nucleus. The key molecules that can be potentially targeted are highlighted, and a discussion on their applicability as alternative preventive means against HPV infection, with a focus on LMIC, is presented.Planar phase-variation microwave sensors have attracted increasing interest in recent years since they combine the advantages of planar technology (including low cost, low profile, and sensor integration with the associated circuitry for post-processing and communication purposes, among others) and the possibility of operation at a single frequency (thereby reducing the costs of the associated electronics). This paper reviews and compares three different strategies for sensitivity improvement in such phase-variation sensors (devoted to material characterization). The considered approaches include line elongation (through meandering), dispersion engineering (by considering slow-wave artificial transmission lines), and reflective-mode sensors based on step-impedance open-ended lines. It is shown that unprecedented sensitivities compatible with small sensing regions are achievable with the latter approach.